Push Button with Arduino Tutorial | Arduino button Interface

Welcome back to Techatronic, in this article, I am gonna do a brief description of the Arduino Button tutorial. if you are a learner and want to learn Arduino by this Arduino tutorial series.

recently we have uploaded blink led with Arduino tutorial.

Table of Contents

Introduction

Arduino is an open-source multipurpose development board that can be used to learn and automate small things in daily life like a curtain riser.

and there are many other applications like stepper motor rotation and pixel-led driving with the Arduino. push button with Arduino helps you to learn to control the project with one push-button or switch and

it will also help you to learn the Coding part. so .let’s start the tutorial.

What is Push Button with Arduino Activity?

So first we will understand the working principle of this experiment. There are a lot of communication pins on an Arduino but in this experiment,

we will use the digital pins of the Arduino. there are 14 digital pins in the Arduino Uno so we will use that digital pins in this experiment. we can use digital pins as input pins as well as output pins.

so now we will use both functions of the pins in this experiment which is push-button interfacing with the Arduino. there are two devices to interface with the Arduino one is push-button and the other is an LED bulb.

the push button has to be connected to the Arduino input pins and the LED to be connected to the output pin. This Arduino button Led associated. so when we push the button the LED will glow.

The Push-button has to be connected to the input pins so It can read the push button.

when you press the push button then the edge of the attitude will change.

for example the voltage change from 5v to 0 in binary 1 to 0, in assembly HIGH to LOW you can use the last two in the Arduino language.

How does it work? working

in a push-button with Arduino when you press that button the input voltage will change from high to low.

then the pin connected to the push button gets to recognize and send to the Arduino that it get some value on the input pins.

now the code start to process and the led connected to the Arduino will start to glow. you need to press the push button only the rest of the work will be done by the Arduino and the system.

so,

this is the lesson in the article to learn the input and the output peripheral of the Arduino and the Arduino coding. you need only a few components to make it run.

it will help you to learn the basics of robotics and sensor interfacing.

Components Required for Interface push button with Arduino

Arduino Uno
USB to A type cable
Jumper wires
LED
Push Button
Resistor
Breadboard

Components Table

You can buy the whole components from the given link we have to share the amazon link. from where you can get a good discount on the components.

Arduino button wiring.

Proteus Daigram

Connection Table

Arduino UNO	Push Button 1	220 Ohm Resistor
2 Pin	Terminal 1	Terminal 1
+5, VCC	Terminal 2
GND		Terminal 2
Arduino UNO	LED	220 Ohm Resistor
12 Pin	Anode Pin
	Cathode Pin	Terminal 1
GND		Terminal 2

Now it turns to code the Arduino for the project. if you don’t know how to operate Arduino software install and setup the Arduino IDE app.

Arduino push Button Code

// constants won't change. They're used here to
// set pin numbers:
const int buttonPin = 2;     // the number of the pushbutton pin
const int ledPin =  12;      // the number of the LED pin

// variables will change:
int buttonState = 0;         // variable for reading the pushbutton status

void setup() {
  // initialize the LED pin as an output:
  pinMode(ledPin, OUTPUT);
  // initialize the pushbutton pin as an input:
  pinMode(buttonPin, INPUT);
}

void loop() {
  // read the state of the pushbutton value:
  buttonState = digitalRead(buttonPin);

  // check if the pushbutton is pressed.
  // if it is, the buttonState is HIGH:
  if (buttonState == HIGH) {
    // turn LED on:
    digitalWrite(ledPin, HIGH);
  } else {
    // turn LED off:
    digitalWrite(ledPin, LOW);
  }
}

upload the given code in the Arduino with the given step. all the best.

Video Sample

Buy Our ebook

Learn 10+ basic activities & sensor interfacing with our Arduino ebook. Well explained program. And brief circuit diagram WhatsApp and email support. which will help you to learn basic electronics, Arduino Coding, Sensor interfacing with Arduino, Arduino, and much more. buy Arduino Ebook to learn https://techatronic.com/arduino-ebook/

Push button with Arduino Tutorial #5